explore the full range at www.iccons.com.au TYPE 17 ROOFING AND CLADDING SCREWS CYCLONIX® TYPE 17 HEX HEAD | Coarse Thread — 14 Gauge IC Find# Part Number Size Description Head/Drive Size Thread Length Base Material Thickness - Timber Finish 670X T17HXTG14050C4X 14-10 x 50 Hex 3/8” 35mm 25mm C4 674X T17HXTG14065C4X 14-10 x 65 50mm 35mm 524X T17HX14075C4X* 14-10 x 75 *Part No. T17HX14075C4X is suitable for cyclonic applications subject to letter of opinion from FYFE Consulting Engineers (Ref. 51176-5). This part is not referenced in the NT Deemed to comply manual (DTCM). TYPE 17 HEX HEAD TOP GRIP | Coarse Thread — 12 & 14 Gauge IC Find# Part Number Size Description Head/Drive Size Thread Length Base Material Thickness - Timber Finish 546W T17HXTG1250C4W 12-11 x 50 Hex 5/16” Full 30mm C4 548W T17HXTG1265C4W 12-11 x 65 IC Find# Part Number Size Description Head/Drive Size Thread Length Base Material Thickness - Timber Finish 519W T17HXT14050C5W 14-10 x 50 Hex 3/8” 33 mm 35 mm C5 POLY-SHOTS® | Coarse Thread — 12 Gauge IC Find# Part Number Size Description Head/Drive Size Thread Length Base Material Thickness - Timber Finish 690 T17HXPS12050C4-100 12-14 x 50 Hex 5/16” 25mm 25mm C4 691 T17HXPS12050C4-250 12-14 x 50 (Bulk Box) TYPE 17 SCREWS TYPE 17 BUGLE BATTEN SCREWS | Course Thread — 14 Gauge IC Find# Part Number Size Description Head/Drive Size Thread Length Base Material Thickness - Timber Finish 571 T17BB14050SS-316 14-10 x 50 Bugle / Hex5 30mm 30mm 316 (A4) SS 581 T17BB14075SS-316 14-10 x 75 50mm 35mm 583 T17BB14100SS-316 14-10 x 100 65mm 573 T17BB14050SS 14-10 x 50 30mm 30mm 302 (A2) SS 582 T17BB14075SS 14-10 x 75 50mm 35mm 584 T17BB14100SS 14-10 x 100 65mm 572MG T17BB14050C3-MG500 14-10 x 50 30mm 30mm C3 573MG T17BB14065C3-MG500 14-10 x 65 43mm 35mm 574MG T17BB14075C3-MG500 14-10 x 75 43mm 576MG T17BB14100C3-MG500 14-10 x 100 67mm 578MG T17BB14125C3-MG500 14-10 x 125 83mm 580MG T17BB14150C3-MG250 14-10 x 150 83mm 590MG T17BB14200C3-MG250 14-10 x 200 117mm 585 T17BB14050ZY 14-10 x 50 30mm 30mm Zinc Yellow 586 T17BB14075ZY 14-10 x 75 50mm 35mm 588 T17BB14100ZY 14-10 x 100 65mm ICCONS® recommended finish (coating / material) of screws for use in the corrosive categories/environment in accordance with AS3566.2-2025 ISO9223, AS4312, AS/NZS 2312.2 AS3566.2 Category Corrosivity § C1 - Very low C2 - Low C3 - Medium C4 - High C5 - Very low CX - Extreme AS3566.2 Typical Characteristics of the Categories § Indoor, dry, air conditioned Most areas of Australia & NZ beyond 50 km from the sea but can be as close as 1 km from seas that are relatively sheltered & quiet Coastal areas with low salinity, urban & industrial areas with low pollution, varies significantly with factors such as winds, topography & vegetation Occurs mainly on the coast. In areas with rough seas & surf, it extends from several hundred meters to 1 km inland Normally found 50 m to 500 m inland from the shoreline of coasts exposed to surf or very rough seas & aggressive industrial areas Offshore locations or within 50 m of the shoreline of breaking surf or very rough seas but could possibly extend to 200 m under the most severe sea conditions ICCONS® Coating Name 1), 2) ICCONS® Head Mark AS3566.2 Corrosion Resistance Classification Zinc Clear / Zinc Yellow IC Class 1 NR NR NR NR NR - - Class 2 NR NR NR NR NR NAUTILUS® 3 IC3 Class 3 NR NR NR Ruspert® Kaitex Mech. Galvansied C3 NAUTILUS XTEND® 3 IC3X NAUTILUS® 4 IC4 Class 4 NR NR NAUTILUS XTEND® 4 IC4X NAUTILUS XTEND® 5 IC5X ———^ NR Stainless Steel* ICS, IC-A2, IC-A4 Stainless Steel (300 Series)* * Stainless Steel: Consideration needs to be given to materials compatibility to avoid bimetallic corrosion. Check with ICCONS® Engineering Department and roll-former supplier of the cladding / roofing / material to be fixed using the stainless steel screws for suitability and compatibility. § For full details on Atmospheric Corrosivity Categories and Resistance Classifications, please refer to AS3566.2-2025 and the referenced standards ISO 9223, AS4312 and AS/NZS 2312.2. NR - Not Recommended 1)The coating information provided above primarily pertains to ICCONS screw coatings intended for roofing and cladding applications, in accordance with AS 3566.2:2025. 2)Some of the ICCONS screw coatings listed above are designed for applications beyond roofing and cladding. For these coatings, corrosion classifications and corrosivity categories are provided as a general guide only. A qualified design professional should review and approve the suitability of any screw coating for the specific application before specification and use. ^AS 3566.2 does not provide coating classification beyond Class 4 however IC5X is suitable for use up to corrosive category 5 CORROSIVE ENVIRONMENT INFORMATION 401 HG AB FA MH SP BC LU PT TC AD HT MR SC CS MA PU TG TP AU LR PA SS EI ME SE TM WE
RkJQdWJsaXNoZXIy ODM0MDI=